E/Z Purge(R)

E/Z Purge(R) is an ammonia-free, water-based product that removes and cleans unwanted color, material or burned polymer from extruders, injection or blow molding equipment. Purging is a critical part of routine maintenance but costly in terms of system downtime, wasted materials, and labor costs. The efficient action of cleaning and purging with E/Z Purge(R) enables you to make quick, complete changeovers from one color to another and from one resin type to another using your own scrap resin. E/Z Purge(R) is safe for workers and the environment.

3 Levels of Purging Excellence

E/Z Purge(R): To be used as a quick, economical method to clean injection and blow molding machines and film and sheet extruders which are of a clean, smooth design with minimal changes of resin and routine, frequent cleaning, works well with PE and PP.

E/Z Purge(R) Heavy Duty: To be used where mold designs are more complicated, product runs are longer, color and resin changes more frequent, works well with PP, PE, Nylon and Polyester. Works well when mixed with scrap scryllic or any type of scrap resin for a more aggressive purge.

E/Z Purge(R) Super: To be used where mold designs are more complicated, product runs are shorter, color and resin changes more frequent, works well with more rigid materials, PVC, Nylon and Polycarbonate and especially with molds prone to produce burnt polymer. Works well when mixed with scrap acryllic or any type of scrap resin for a more aggressive purge.

Features

• No need to purchase more resin; mixes with your own scrap resin.
• Ammonia-free.
• Water-based.
• Easy-feeding.
• Odor free.
• No residues.
• Environmentally safe.

• Injection molding.
• Blow molding.
• Extrusion.
• Co-extrusion.

Typical Properties

Directions for Use

1. Fill a plastic container with double the amount of resin needed to fill the extruder barrel, or the amount usually used, if less.
2. Spray E/Z Purge(R) into the resin, mixing thoroughly using non-absorbent gloves, at approximately 2% of E/Z Purge(R) by weight. Example: 12 lbs. of resin = 4 oz. of E/Z Purge(R); 50 lbs. of resin = 1 lb. of E/Z Purge(R). Simply multiply your pounds of resin by .02 and that will indicate the amount of E/Z Purge(R) to use.
3. Set the zone temperatures of your machine slightly lower than normal operating temperature.
4. INJECTION AND BLOW MOLDING: Feed the E/Z Purge(R) resin mix into the hopper very slowly with the extruder set at 10 to 15 RPM. Continue feeding the purge mix until you see the material coming out of the die. When the material comes out from the die, stop the screw for several minutes to let the E/Z Purge(R) work. Start up again and feed the next resin into the machine.
5. FILM AND SHEET EXTRUDERS: Use the same procedure above but wait 10 to 15 minutes before starting up again.
6. Before feeding new resin into hopper, be sure that all moisture is removed and screw is stopped while drying.
7. For very dirty machines or severely burned on material, the above procedures may need to be repeated.
8. Using E/Z Purge(R) in a weekly preventive maintenance program can eliminate polymer buildup on machine parts.

Safety

Elm Grove Industries, Inc. is a global supplier of specialty chemical products for the plastics and packaging industries.

The information contained herein is intended to assist you in determining the suitability of our product for your commercial or industrial applications. As performance characteristics vary according to application, operating conditions, use, etc., we recommend that you test our products to determine to your satisfaction that quality and performance are suitable for your particular purpose. Nothing herein shall constitute a warranty of any kind, express or implied, including but not limited to warranty of merchantability or fitness, nor is protection from any patent to be inferred.

Elm Grove Industries, Inc., PO Box 659, 910 Elm Grove Rd., Elm Grove, WI 53122. Tel: 262-797-9244; Fax: 262-797-9763.